Carbon Nanotube-, Boron Nitride-, and Graphite-Filled Polyketone Composites for Thermal Energy Management.

In order to improve the thermal conductivity of 30 wt % synthetic graphite (SG)-filled polyketones (POKs), conductive fillers such as multiwall carbon nanotubes (CNTs) and hexagonal boron nitride (BN) were used in this study. Individual and synergistic effects of CNTs and BN on 30 wt % synthetic graphite-filled POK on thermal conductivity were investigated. 1, 2, and 3 wt % CNT loading enhanced the in-plane and through-plane thermal conductivities of POK-30SG by 42, 82, and 124% and 42, 94, and 273%, respectively. 1, 2, and 3 wt % BN loadings enhanced the in-plane thermal conductivity of POK-30SG by 25, 69, and 107% and through-plane thermal conductivity of POK-30SG by 92, 135, and 325%. It was observed that while CNT shows more efficient in-plane thermal conductivity than BN, BN shows more efficient through-plane thermal conductivity. The electrical conductivity value of POK-30SG-1.5BN-1.5CNT was obtained to be 1.0 × 10-5 S/cm, the value of which is higher than that of POK-30SG-1CNT and lower than that of POK-30SG-2CNT. While BN loading led to a higher heat deflection temperature (HDT) than CNT loading, the hybrid fillers of BNT and CNT led to the highest HDT value. Moreover, BN loading led to higher flexural strength and Izod-notched impact strength values than CNT loading.

Resveratrol prevents ovariectomy-induced bone quality deterioration by improving the microarchitectural and biophysicochemical properties of bone.

INTRODUCTION: Osteoporosis is a major health problem that is very common worldwide and is characterized by both low bone density and deterioration in bone quality. New treatment options without side effects have become an active area of research in recent years. This study was designed to investigate the preventive effects of resveratrol on bone quality deterioration caused by ovariectomy. MATERIALS AND METHODS: Sixty rats were randomly divided into five groups (12 animals per group): Control, Sham-operated (SHAM), ovariectomized (OVX), OVX + Resveratrol-40 mg/kg/day (OVX + Res40), OVX + Resveratrol-80 mg/kg/day (OVX + Res80). Resveratrol was administered by oral gavage (40 and 80 mg/kg/day) for ten weeks. Micro-CT measurements, biomechanical testing, Raman spectroscopy analysis, and RT-PCR analysis were performed. ALP, OCN, TAS, and TOS levels were also measured from blood serum. RESULTS: Bone strength, bone volume/total volume, trabecular volume, and trabecular thickness were higher in the OVX + RES-80 group than in the OVX group. Resveratrol increased osteogenic differentiation, as the expression of osteogenic markers ALP, Col1A1, Runx2, OPG, OCN increased in both OVX + RES-80 and OVX + RES-40 groups compared to the OVX group. 80 mg/kg/day resveratrol administration decreased the levels of ALP, OCN and TOS in ovariectomized rats. Raman spectroscopy findings showed a preventive effect of resveratrol administration against ovariectomy-induced deterioration in biophysiochemical properties of bone tissue. CONCLUSION: This study revealed that administration of different doses of 80 mg/kg/day and 40 mg/kg/day of resveratrol had protective effects on bone quality deterioration caused by ovariectomy.

Improving Flame Retardant Properties of Aliphatic Polyketone (POK)-Based Composites.

The effect of zinc borate (ZB) and high-molecular-weight siloxane (SIL) on flame retardancy, mechanical, and thermal properties of aliphatic polyketone (POK)-containing aluminum diethyl phosphinate (OF) was investigated in this study. Ten wt % OF is sufficient to obtain V0 rating according to the UL94 test. As the weight fraction of OF was increased, the flame retardancy properties and LOI values improved, while the tensile and impact properties decreased. To avoid the degradation in mechanical and impact properties as much as possible and obtain the same and better flame retardancy properties, synergists such as SIL and ZB were used. Flame retardancy of POK-based composites was determined by the limiting oxygen index (LOI) test, UL94 measurement, and cone calorimeter test. The additions of 1 wt % SIL and ZB have not led to a considerable decrease in the tensile strength and impact properties of POK-10OF. While ZB and SIL are very efficient in decreasing the smoke density, ZB is more efficient than SIL in increasing the LOI value of the composite. The addition of 1, 2, and 4 wt % ZB and SIL synergists did not lower their UL94 ratings. Moreover, it can be added that ZB is more efficient than SIL in decreasing the fire growth rate (FIGRA) and maximum average rate of heat emission (MARHE) values. Using OF (10 wt %) and ZB (4 wt %), LOI values higher than 32% and smoke density values lower than 150 were obtained.

Comparison of the Thermal and Mechanical Properties of Poly(phenylene sulfide) and Poly(phenylene sulfide)-Syndiotactic Polystyrene-Based Thermal Conductive Composites.

Syndiotactic polystyrene (SPS) has attracted considerable attention recently due to its high melting temperature, low cost, and relatively low density value. The aim of the study is to reveal whether a blend of PPS and SPS (PPS-SPS) can be used instead of PPS for high thermal stability, high mechanical performance, and high thermal conductive material applications. For this aim, poly(phenylene sulfide)/syndiotactic polystyrene-based carbon-loaded composite materials were prepared using a twin screw extruder. Two carbon-based materials, carbon fiber (CF) and synthetic graphite (SG), were used to improve the mechanical properties and thermal conductivity of the PPS-SPS blends. Through-plane conductivity values of PPS-30SG-10CF and PPS-SPS-30SG-10CF were obtained to be 13.67 and 12.92 W/mK, with densities of 1.55 and 1.50 g/cm3, respectively. It was demonstrated that PPS-SPS blend-based carbon-loaded composites have great potential to be used in thermal management applications with the advantages of relatively low cost and lightweight compared to PPS-based composites.

Investigation of the Fire Performance of Polyamide 6-Based Composites with Halogen-free Flame Retardants and Synergistic Materials.

In this study, halogen-free flame retardants and metal synergist materials were used to enhance the flammability of PA6. PA6-based composites including various fractions of additives were manufactured using a twin-screw extruder and an injection molding machine. Mechanical, thermal, physical, morphological, and flame retardant properties were investigated with several characterization methods. The study aims to meet R22 requirements based on the EN45545 standard for fire protection of railway vehicles, according to which limiting oxygen index (LOI), smoke density, and conventional index of toxicity (CIT) values under HL3 hazard levels have to be min 32%, max 300, and max 1.5, respectively. 15FR-2MH, 15FR-5MH, 15FR-1MH-1ZB, 15FR-1MH-1BOH, and 15FR-1MH-1SIL composites exhibited both the required smoke density, CIT, and LOI values for R22. It can be said that hybrid synergists provide all requirements according to the R22-EN45545 standard. Instead of using 15FR-2MH, 15FR-1MH-1BOH led to a lower smoke density value for PA6.

Size effects of graphene nanoplatelets on the properties of high-density polyethylene nanocomposites: morphological, thermal, electrical, and mechanical characterization.

High-density polyethylene (HDPE)-based nanocomposites incorporating three different types of graphene nanoplatelets (GnPs) were fabricated to investigate the size effects of GnPs in terms of both lateral size and thickness on the morphological, thermal, electrical, and mechanical properties. The results show that the inclusion of GnPs enhance the thermal, electrical, and mechanical properties of HDPE-based nanocomposites regardless of GnP size. Nevertheless, the most significant enhancement of the thermal and electrical conductivities and the lowest electrical percolation threshold were achieved with GnPs of a larger lateral size. This could have been attributed to the fact that the GnPs of larger lateral size exhibited a better dispersion in HDPE and formed conductive pathways easily observable in scanning electron microscope (SEM) images. Our results show that the lateral size of GnPs was a more regulating factor for the above-mentioned nanocomposite properties compared to their thickness. For a given lateral size, thinner GnPs showed significantly higher electrical conductivity and a lower percolation threshold than thicker ones. On the other hand, in terms of thermal conductivity, a remarkable amount of enhancement was observed only above a certain filler concentration. The results demonstrate that GnPs with smaller lateral size and larger thickness lead to lower enhancement of the samples' mechanical properties due to poorer dispersion compared to the others. In addition, the size of the GnPs had no considerable effect on the melting and crystallization properties of the HDPE/GnP nanocomposites.

Characterization​ and ​analysis of ​m​otion ​m​echanism​ of electroactive​ chitosan-based actuator.

In order to analyze the bending mechanism of the electroactive​ chitosan-based actuator, different amounts of poly(diallyldimethylammonium chloride) (PDAD) were incorporated in chitosan solution. The effects of PDAD concentration on electromechanical performance of chitosan actuator were investigated under various excitation voltages. With the incorporation of PDAD into chitosan solution, crosslinked chitosan film acts as an actuator showing a considerable displacement behavior. However it can be noted that higher incorporation of PDAD into chitosan solution decreased the performance of the actuators. Thermal, viscoelastic, and crystallographic properties of the chitosan films were examined by thermogravimetric analysis, dynamic mechanical analysis, and X-ray diffraction analysis, respectively. The effect of incorporation of PDAD in chitosan-based film on morphological properties of chitosan film was determined by scanning electron microscopy. It was observed that the films involving PDAD have larger pore size than the PDAD free film.

Three-dimensional finite element analysis of stress distribution of two-retainer and single-retainer all-ceramic resin-bonded fixed partial dentures.

OBJECTIVE: A long-term clinical study previously stated that adhesively luted resin-bonded fixed partial dentures (RBFPDs) with two retainers exhibited two complications (loss of adhesion or fracture between retainer and pontic) when compared to RBFPDs with a single retainer. The reasons for these complications were not reported. The aim of this study was to evaluate the stress distribution of two-retainer and singleretainer zirconium dioxide RBFPDs by using three-dimensional finite element analysis (3D FEA). METHOD AND MATERIALS: Two different 3D finite element models were created. Each model contained cortical bone, cancellous bone, periodontal ligament, cement, and enamel. Additionally one of the models contained a two-retainer zirconium dioxide RBFPD while another contained a single-retainer zirconium dioxide RBFPD. A 100 N force was applied at 45 degrees 2 mm below the incisal edge of the palatal surface of the pontic. In each model, Von Mises stress distribution was evaluated. RESULTS: Maximum Von Mises stress values in RBFPD with a single retainer and two retainers were 1.13 MPa and 1.23 MPa, respectively. Von Mises stress was concentrated at the interface between pontic and retainer for RBFPD with two retainers. CONCLUSION: Zirconium dioxide RBFPD with a single retainer and two retainers exhibited similar stress concentrations between pontic and retainer. However, the use of a single retainer for RBFPDs prevented stress concentration at the interface between retainer and pontic.

Sodium tungstate alleviates biomechanical properties of diabetic rat femur via modulation of oxidative stress.

Diabetes mellitus leads to bone disorders such as osteopenia and osteoporosis that can increase fracture risk. On the other hand, sodium tungstate is an inorganic compound which exerts anti-diabetic activity in experimental studies due to its suggested insulin-mimetic or antioxidant activity. Therefore this study was designed to investigate the effect of tungstate on bone quality in diabetic rat femurs. The rats were divided into four groups: Control (C), tungstate-treated control (C+Tung), diabetes (STZ-D) and tungstate-treated diabetes (STZ-D+Tung). Diabetes mellitus was induced by single injection of streptozotocin (50 mg/kg). The treated rats received 150 mg/kg/day of sodium tungstate for 12 weeks. Sodium tungstate achieved a little (17%) but significant reduction on blood glucose levels, while it didn't recover the reduced body weights of diabetic rats. In addition, impaired bone mechanical quality was reversed, despite the unchanged mineral density. Sodium tungstate administration significantly lowered the 2-thiobarbituric acid reactive substances and restored the activity of tissue antioxidant enzymes such as glutathione peroxidase, catalase and superoxide dismutase in diabetic rats. On the other hand, glutathione levels didn't change in either case. These findings indicate that tungstate can improve the reduced mechanical quality of diabetic rat femurs due probably to reduction of reactive oxygen species and modulation of antioxidant enzymes as well as reduction in blood glucose levels.

Effect of angiotensin II type 1 receptor blocker on osteoporotic rat femurs.

BACKGROUND: Osteoblasts and osteoclasts are known to express Ang II type I (AT1) receptor in cell cultures, suggesting the existence of local renin-angiotensin system (RAS) in bone. This study was designed to investigate the effects of losartan as AT1 receptor blocker on ovariectomized rats' femur. METHODS: Losartan (5 mg/kg/day) was administered via oral gavage for 8 weeks. Bone mineral density (BMD) was measured using dual energy X-ray absorptiometry, while tensile and three-point bending tests were performed for evaluation of biomechanical properties of bone. The trabecular porosity was analyzed by scanning electron microscopy. RESULTS: There was a significant decrease in BMD values of ovariectomized rats' femurs which were reversed by losartan treatment. According to tensile test results, ultimate tensile strength and strain values of losartan treated ovariectomized rats' femurs increased and decreased, respectively, when compared to that of ovariectomized animals. Losartan treatment also caused a significant recovery in flexural strength and modulus parameters regarding respective control values, which mean losartan treated ovariectomized rats' femur had more force tolerance until break than ovariectomized rats' femur. Quantitative microscopic analysis showed larger trabecular porosity in ovariectomized rats than control rat femurs and it was significantly decreased after losartan treatment. CONCLUSION: Blockage of AT1 receptor increased strength, mass and trabecular connections of ovariectomized rat femurs. Therefore, it is tempting to speculate that drugs, including AT1 receptor blockers, may be used for the treatment of osteoporosis or reduction of its detrimental effects in the future.

Fracture resistance and analysis of stress distribution of implant-supported single zirconium ceramic coping combination with abutments made of different materials.

The purpose of this study was to compare the fracture resistance and fracture mode of single implant-zirconium coping combinations using zirconium and titanium abutments and to analyze the stress distribution pattern using three-dimensional finite elements analysis. Twenty implants with titanium and zirconium abutments were randomly divided into two groups (n = 10) and into resin blocks. Zirconium copings were cemented onto the abutments. The specimens were loaded with 135° angles to the long axis and the load values at the moment of failure were recorded using a universal test machine. Stress levels were calculated according to the maximum Von Mises criteria. The fracture resistances for titanium and zirconium abutment groups were 525.65 N and 514.05 N, respectively. No significant differences were observed between two groups regarding the fracture resistance levels. The maximum Von Mises equivalent stress concentrated on zirconium copings in both of the groups. Implant-abutment-ZrO2 coping combination has the potential to withstand physiological occlusal forces in the anterior region. Three-dimensional finite elements analysis results of the implant-abutment-ZrO2 coping combination is compatible with the results of fracture resistance.

Effect of noble metal alloy post and core material on the fracture resistance of endodontically treated teeth.

The aim of this study was to investigate the effect of one particular brand of post and core system (ER Post) consisted of different post and core materials on the fracture resistance of endodontically treated teeth. Fifty caries-free maxillary central incisors were randomly assigned to five groups (n=10). All teeth were sectioned at the cemento-enamel junction except for the teeth in the control group. Four experimental groups consisted of cast gold post-and-core group (GG), Heraplat post/cast gold core group (HG), titanium post/composite core (TC), and titanium post/cast gold core (TG). The control group (ETT) consisted of endodontically treated teeth without posts. All posts were cemented in the roots with zinc phosphate cement. Following thermal cycling (5000 cycles between 5 degrees C and 55 degrees C with a dwell time of 30 seconds) a static load was applied to 2 mm below the incisal edge on the palatal surface of each specimen until they were fractured. Fracture data obtained and statistically analyzed with one-way ANOVA and a Tukey's test (p<0.05). Means of the fracture resistance during static loading were: 423.76 N (GG), 529.46 N (HG), 389.08 N (TC), 408.7 N (TG), 404.4 N (ETT, control). Heraplat post with cast gold core exhibited the highest fracture load than the other groups (p<0.05). Specimens in groups HG and ETT (control) showed the most repairable failure. Heraplat post with cast gold core had the highest fracture resistance of endodontically treated teeth.

Fracture resistance of endodontically treated teeth: effect of tooth coloured post material and surface conditioning.

This in vitro study evaluated the effects of the different endodontic posts and surface conditioning on the fracture resistance and fracture modes of endodontically treated teeth. The experimental groups consisted of zirconia ceramic post with a glasss-ceramic core [A], zirconia ceramic post with a composite core [B], glass fiber composite post (FRC) with a composite core [C], and titanium post with a composite core [D]. All posts in these groups were cemented with self-adhesive resin cement (Rely X Unicem Aplicap) combination with tribochemical silica coating (TSC). Groups E, F, G and H comprised the same post-and-core materials as the first 4 groups but cemented with the same resin cement without TSC. Specimens were subjected to thermal cycling between 5 degrees C and 55 degrees C for a total of 5000 cycles with 30s per cycle. Static load was applied to the palatal surface of each specimen until they were fractured. Statistical analysis was conducted using analysis of variance (ANOVA) followed by post-hoc comparisons (Tukey). The fracture resistance was significantly affected by the post material (P < 0.001) and surface conditioning (P < 0.001; two-way ANOVA). The application of TSC to post surface decreased the fracture resistance of zirconia ceramic post with composite core (p=0.002; Tukey) and glass FRC post with composite core (p=0.029; Tukey). No catastrophic failure was observed for groups B, C, D, E, F and G. Under the testing conditions used, the titanium post/composite core that had been silicoated exhibited the highest fracture resistance.

A biomechanical study on preloaded compression eVect on headless screws.

INTRODUCTION: Commonly used headless design screws such as Acutrak and Herbert screws have limited compressive effect on short fragment fixation. Therefore, we investigated whether preloaded compression techniques could be helpful in improving the compression effect. METHOD: A prototype of interfragmentary compression screw was designed with a constant pitch to avoid self-compressive effect. Preloaded compression was achieved with a sleeve device before the insertion of the trailer side (the leading side was inserted). Prototype screw test results were compared with those of Acutrak and Herbert screws. Eight pullout and eight compression tests were performed for each of the three screws using homogenous synthetic bone blocks. RESULTS: The mean pullout forces of the Acutrak, Herbert and prototype screws were 67.21, 45.90 and 61.88 N, respectively. Preloaded compression (18.15 N) was higher than the compression produced by Acutrak (15.27 N) and Herbert (15.11 N) screws (p < 0.05). However, at the end of full insertion, half of the power obtained by preloaded compression was lost. CONCLUSION: Preloaded compression technique was successful in attaining maximum compression rate. During trailing-side insertion, constant pitch design failed to keep compression rate. Variable pitches can be useful to preserve or increase compression rate. In addition, sleeve usage may be more advantageous in thin fragment fixation.